Do VLANs within a subnet need to have their own subnet for router on a stick?Best Practice(?): 2 publicly...
Accidentally leaked the solution to an assignment, what to do now? (I'm the prof)
Watching something be written to a file live with tail
What typically incentivizes a professor to change jobs to a lower ranking university?
How do we improve the relationship with a client software team that performs poorly and is becoming less collaborative?
Finding angle with pure Geometry.
Is a conference paper whose proceedings will be published in IEEE Xplore counted as a publication?
What's the point of deactivating Num Lock on login screens?
What are the differences between the usage of 'it' and 'they'?
Font hinting is lost in Chrome-like browsers (for some languages )
How do I create uniquely male characters?
What defenses are there against being summoned by the Gate spell?
Which models of the Boeing 737 are still in production?
Have astronauts in space suits ever taken selfies? If so, how?
How is it possible to have an ability score that is less than 3?
How can bays and straits be determined in a procedurally generated map?
How does one intimidate enemies without having the capacity for violence?
Is it unprofessional to ask if a job posting on GlassDoor is real?
I’m planning on buying a laser printer but concerned about the life cycle of toner in the machine
Show that if two triangles built on parallel lines, with equal bases have the same perimeter only if they are congruent.
Can a Warlock become Neutral Good?
To string or not to string
Either or Neither in sentence with another negative
Test if tikzmark exists on same page
Writing rule stating superpower from different root cause is bad writing
Do VLANs within a subnet need to have their own subnet for router on a stick?
Best Practice(?): 2 publicly available subnet VLANs and inter VLAN routingSplitting up a flat network into VLANsI have two vlans on the same router that can't ping each otherVLans Cisco Packet tracerMultiple VLANs under one subnet (for traffic control)Router requirements for VLANSBest practice for connecting router to switch? (re: VLANs and multiple ports)Help with Native Vlan mismatch errorHow to turn off auto-routing between interfaces in same router ? is there any command for that?Packet-Tracer multiple IPs for a PC
I have been creating a network lab in packet tracer for practice. I have 3 vlans in subnet A and I am trying to configure router on a stick at gig6/0 on the bottom left of the image. Do I need to create a subnet for each VLAN in order for the router on a stick gateway to work?
router vlan subnet trunk gateway
edited 3 hours ago
Cown
6,90631031
asked 6 hours ago
Jon StinnettJon Stinnett
61
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I have been creating a network lab in packet tracer for practice. I have 3 vlans in subnet A and I am trying to configure router on a stick at gig6/0 on the bottom left of the image. Do I need to create a subnet for each VLAN in order for the router on a stick gateway to work?
router vlan subnet trunk gateway
edited 3 hours ago
Cown
6,90631031
asked 6 hours ago
Jon StinnettJon Stinnett
61
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I have been creating a network lab in packet tracer for practice. I have 3 vlans in subnet A and I am trying to configure router on a stick at gig6/0 on the bottom left of the image. Do I need to create a subnet for each VLAN in order for the router on a stick gateway to work?
router vlan subnet trunk gateway
edited 3 hours ago
Cown
6,90631031
asked 6 hours ago
Jon StinnettJon Stinnett
61
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I have been creating a network lab in packet tracer for practice. I have 3 vlans in subnet A and I am trying to configure router on a stick at gig6/0 on the bottom left of the image. Do I need to create a subnet for each VLAN in order for the router on a stick gateway to work?
router vlan subnet trunk gateway
router vlan subnet trunk gateway
edited 3 hours ago
Cown
6,90631031
asked 6 hours ago
Jon StinnettJon Stinnett
61
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 3 hours ago
Cown
6,90631031
asked 6 hours ago
Jon StinnettJon Stinnett
61
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 3 hours ago
Cown
6,90631031
edited 3 hours ago
Cown
6,90631031
edited 3 hours ago
Cown
6,90631031
6,90631031
asked 6 hours ago
Jon StinnettJon Stinnett
61
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 6 hours ago
Jon StinnettJon Stinnett
61
asked 6 hours ago
Jon StinnettJon Stinnett
61
61
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Jon Stinnett is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered 6 hours ago
Zac67Zac67
32.6k22163
add a comment |
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited 3 hours ago
Cown
6,90631031
answered 5 hours ago
Ron TrunkRon Trunk
39.5k33780
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "496"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fnetworkengineering.stackexchange.com%2fquestions%2f58283%2fdo-vlans-within-a-subnet-need-to-have-their-own-subnet-for-router-on-a-stick%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered 6 hours ago
Zac67Zac67
32.6k22163
add a comment |
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered 6 hours ago
Zac67Zac67
32.6k22163
add a comment |
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered 6 hours ago
Zac67Zac67
32.6k22163
I'm not understanding your exact problem because you don't provide enough detail but maybe this helps:
With rare exceptions, an IP subnet is mapped to a VLAN = broadcast domain = layer-2 network on a 1:1 basis.
You can run multiple IP subnets inside a single VLAN but they need a router to communicate with each other. Most often this setup doesn't make too much sense.
You can't run a single IP subnet across multiple VLANs though (without elaborate workarounds). Nodes in the same subnet expect to be able to talk to each other on a common layer-2 network = VLAN = broadcast domain.
So, your "VLANs within a subnet" can only work when you've split that subnet into sub-subnets properly and set up the router as gateway in between. A router on a stick is a router forwarding between VLAN subinterfaces on a single physical interface. Each subinterface needs to connect to one of the desired VLANs, so the link needs to be a VLAN trunk on both the switch and the router side.
answered 6 hours ago
Zac67Zac67
32.6k22163
edited 1 hour ago
answered 6 hours ago
Zac67Zac67
32.6k22163
answered 6 hours ago
Zac67Zac67
32.6k22163
answered 6 hours ago
Zac67Zac67
32.6k22163
32.6k22163
add a comment |
add a comment |
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited 3 hours ago
Cown
6,90631031
answered 5 hours ago
Ron TrunkRon Trunk
39.5k33780
add a comment |
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited 3 hours ago
Cown
6,90631031
answered 5 hours ago
Ron TrunkRon Trunk
39.5k33780
add a comment |
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited 3 hours ago
Cown
6,90631031
answered 5 hours ago
Ron TrunkRon Trunk
39.5k33780
Just to amplify on Zac’s answer: you have one subnet per vlan and vice versa. At the CCNA level, you can ignore the rare exceptions. The router on a stick has an (sub)interface in each subnet. Therefore all VLANs must be trunked to the router.
edited 3 hours ago
Cown
6,90631031
answered 5 hours ago
Ron TrunkRon Trunk
39.5k33780
edited 3 hours ago
Cown
6,90631031
edited 3 hours ago
Cown
6,90631031
edited 3 hours ago
Cown
6,90631031
6,90631031
answered 5 hours ago
Ron TrunkRon Trunk
39.5k33780
answered 5 hours ago
Ron TrunkRon Trunk
39.5k33780
answered 5 hours ago
Ron TrunkRon Trunk
39.5k33780
39.5k33780
add a comment |
add a comment |
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Jon Stinnett is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Network Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fnetworkengineering.stackexchange.com%2fquestions%2f58283%2fdo-vlans-within-a-subnet-need-to-have-their-own-subnet-for-router-on-a-stick%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
